RC-S2LP-868

€9.00

Tax excluded

RC-S2LP-868 module is based on STMicroelectronics S2-LP transceiver.

This device is a high performance ultra low power RF transceiver designed for RF wireless application in the sub 1GHz band.
The module is designed for maximum performance in a minimal space, with 4 programmable I/O pins.
Programmable from external microcontroller via SPI interface.
For more information and details, please refer to the S2-LP datasheet (www.st.com).

Volume discounts

Quantity	Unit discount	You Save
10	10%	€9.00
20	20%	€36.00

Quantity

In stock

The minimum purchase order quantity for the product is 2.

Politiche per la sicurezza

(modificale nel modulo Rassicurazioni cliente)

Politiche per le spedizioni

(modificale nel modulo Rassicurazioni cliente)

Politiche per i resi

(modificale nel modulo Rassicurazioni cliente)

Description
Product Details

RC-S2LP-XXX module is based on STMicroelectronics S2-LP transceiver.

N.3 Versions available :

- RC-S2LP-434 Freq. : 433MHz

- RC-S2LP-868 Freq. : 868MHz

- RC-S2LP-915 Freq. : 915MHz

Sub-1Ghz technology is becoming one of the chief driving forces behind the Internet of Things (Iot), in particular this type of module is ideal for this applications basically for the following reasons :

Ultra low power consumption, the consumption of this device is 7mA when receiving and 20mA when transmitting at +14dBm (11mA at +10dBm) in sleep mode the consumption is 0.7µA.
Long range operations, the sensitivity parameter is -109dBm at data rates of 38.4 kbps and down to -128dBm when the data rate is 0.3kbps. Interference from other wireless communications can be overcome with 90dB of blocking. The RF output power levels can reach up to +16dBm. All this ensure a robust signaling for long range communications.
Ready for use SMD mounting (15x 22mm)
Metal shield.


Technical Characteristics	MIN	TYP	MAX	UNIT
Supply Voltage	1.8	3.0	3.60	Volt
Supply Current RX mode		7.2		mA
Supply Current TX mode -----> +10dBm		11		mA
Supply Current TX mode -----> +14dBm		20		mA
Supply Current Standby Mode		0,5		µA
Supply Current Shut Down Mode		2.5		nA
Operative Frequency		868		MHz
RF Power Output 50ohm (programmable parameter)	-30		+16	dBm
RF Sensitivity 38.4kbps 2GFSK		-109		dBm
RF Sensitivity 0.3kbps 2GFSK		-128		dBm
Operating Temperature range	-30		+75	°C


Pads	Name	Description	Pin Type
1	SDO	SPI slave data output	Digital out
2	SDI	SPI slave data input	Digital in
3	SCLK	SPI slave clock input	Digital in
4	CSn	SPI chip select	Digital in
5	GPIO-0	General purpose I/O configurable through SPI registers	Digital I/O
6	GPIO-1	General purpose I/O configurable through SPI registers	Digital I/O
7	GPIO-2	General purpose I/O configurable through SPI registers	Digital I/O
8	GPIO-3	General purpose I/O configurable through SPI registers	Digital I/O
9	GND	Connect to GND	Ground pin
10	SDN	Shutdown input pin	Digital in
11	GND	Connect to GND	Ground pin
12	GND	Connect to GND	Ground pin
13	VCC	1.8Volt to 3.6Volt	Power Supply
14	VCC	1.8Volt to 3.6Volt	Power Supply
15	GND	Connect to GND	Ground pin
16	GND	Connect to GND	Ground pin
17	GND	Connect to GND	Ground pin
18	GND	Connect to GND	Ground pin
19	GND	Connect to GND	Ground pin
20	ANT	Connect to external Antenna	Antenna
21	GND	Connect to GND	Ground pin

EVALUATION BOARD -----> RC-S2LP-XXX-EW

The RC-S2LP-XXX-EW is an evaluation board based on the RC-S2LP-XXX module.

The Evaluation board can be used instead of those provided by the chip manufacter (www.st.com) denominated STEVAL-FKIXXXV2.

With this board it is possible to use all the SW resources provided for the development activity, in particular :

- STSW-S2LP-DK (S2-LP-DK Application Notes)
- STSW-S2LP-SFX-DK (S2-LP SigFox Demo)

RC-S2LP-XXX signal test points are split across two rows which are Arduino compliant connectors: CN1, CN2 and Cn3, CN4. The RC-S2LP-XXX shield is connected to the Nucleo motherboard via the Arduino compliant connectors.

In stock 100 Items

Data sheet